Simplicity 2418 Shirt (Its So Easy): View B

Simplicity 2418 Shirt: view B
Simplicity 2418 Shirt: view B
Ok, so far sewing has been a challenge. But I am still excited to learn how to make my own handmade clothes. I know that I will have to learn a lot in order to make anything successfully, and I continuously struggle to understand pattern instructions (which seem to be written in code). My latest project, (Its so Easy) Simplicity 2418 has been my most difficult project so far. I used a smooth polyester fabric that is supposed to resemble silk.

I made the slit front version (View B), not the cowl neck version.  I don’t do cowl necks, although Katiekadiddlehopper made a gorgeous version that suits her perfectly. Two specific parts of this pattern were difficult for me to make: the front of the shirt (the v-shaped part: step 7) and the yoke (step 12).

Step 7 (the front of the shirt) includes lots of stitches that must meet at the correct point for the shirt front to lie smooth and flat.

The yoke was a particular challenge because I had no idea what a yoke was. When I hear yoke, I think ‘oxen’. The pattern instructions for how to attach the yoke are on Step 12. Unfortunately the illustration for step 12 was created by a blind drunkard. Here I have reproduced it:

Simplicity 2418 Top Pattern
Artist's Rendition of Step 12

Thankfully, the pattern instructions explain what is going on in step 12. These instructions were very helpful. Here they are:

12.  Aliquam lorem ante, dapibus in, viverra quis, feugiat a, tellus. Phasellus viverra nulla ut metus varius laoreet. Quisque rutrum. Aenean imperdiet. Etiam ultricies nisi vel augue.Curabitur ullamcorper ultricies nisi. Nam eget dui. Etiam rhoncus. Maecenas tempus, tellus eget condimentum rhoncus, sem quam semper libero, sit amet adipiscing sem neque sed ipsum

Is that clear?

It was at this point that I realized that the pattern authors must have decided to start condensing the pattern instructions to an unreasonable degree so they did not have to include a third piece of paper in the pattern instructions.  Another piece of paper would have cut into the profits.

It took 3 full muslins for me to figure out this pattern, and it still looked terrible.  Here are my tips for help on Simplicity 2418 if you are a novice:

1. Make a muslin.  Use large baste stitches so you can try again if/when you mess up. Don’t backstitch so it is easier to pick out the stitches. You don’t need to make a full length version of the shirt, just work on the neck, yoke and top of the back.

2. For STEP 7: Remember what our friends the Ghostbusters taught us: DON’T CROSS THE SEAMS.  You will sew 3 different stitches to meet at the center low point for the shirt slit.

Simplicity 2418 Yoke
Simplicity 2418 Yoke

Have the exact point in mind where you need to stop sewing so each one of the three stitching sequences do not cross each other. Otherwise the front of the shirt won’t lie flat.

3. For STEP 12, you will be enclosing the raw edge of the back of the shirt inside of the raw edge of the yoke. The aforementioned Step 12 illustration fails to make this clear. If you are a complete yoke novice like me, remember that the yoke is not spread open in the shirt.  It is folded wrong sides together, so you have the right side of the fabric both facing outward and also against your back (just in the yoke portion) in the final completed version of the shirt. I noticed that Miss P mentioned that the yoke instructions were confusing, so if an experienced seamstress feels that way then I don’t feel too bad about being a bit lost.

Here are some details on how to attach the yoke, in case anyone else needs help with step 12. There is probably a better way to do this, but at least this will get the shirt made.

  1. Simplicity 2418 Yoke Help
    Start by enclosing the back of the shirt in the Yoke, aligning the raw edges

    Start by opening up the two pieces of fabric that make up the yoke. Place it wrong side up. You should have already folded up and pressed 5/8 of an inch of the yoke’s raw edges. Place the back of the shirt so that the raw edge of the back of the shirt is aligned with the right side of the yoke flap. Pin and sew, as the directions state.







  2. The directions state to attach the font of the shirt to the shoulder of the yoke. I think you can finish attaching the back of the shirt to the yoke (my step 3) first, but in the end it doesn’t seem to matter as either way will work.
  3. Simplicity 2418 View B Yoke
    Simplicity 2418 View B Yoke

    The Yoke is now partially attached to the back of the shirt. Fold the yoke closed so that the wrong sides of the two pieces of the fabric are together. Align the pressed folded edge of the yoke so that it aligns with the back of the shirt, covering up the raw edge and creating a neat line. Pin and sew as in the directions.









  4. Simplicity 2418 Shirt Pattern View B
    Simplicity 2418 Shirt Pattern View B

    After you have completed Step 12 and attached the front of the shirt to the shoulder portion of the yoke, you will have a nice even neck hole, pleats at the front of the shoulders, and gathering at the center of the back. You are ready to complete the arm holes and sew up the sides of the shirt next.

Ultimately, the sleeves on this shirt don’t suit me, and the shirt looks a bit shapeless even though I made a size smaller. The sleeves stick out too far as the edges are stiff, when they should drape down my shoulders and my arms. This makes the shirt unwearable.

I thin I might have a bit more luck with this pattern after I have a bit more sewing experience.

Leave a Reply

Your email address will not be published. Required fields are marked *